Supero AS-1010S-T Скачать руководство пользователя

Страница: 11 / 100

Chapter

Introduction

1-1 Overview

The AS1010S-T is a single processor, mini 1U rackmount server comprised of two

main subsystems: the SC811FT-260 chassis and the H8SSL-i motherboard. The

H8SSL-i supports a single AMD Opteron 100 series processor in a 939-pin socket

and up to 4 GB of unbuffered DDR400/333 SDRAM memory. Please refer to our

web site for information on operating systems that have been certiﬁ ed for use with

the 1010S-T and for regular updates on supported processor speeds.

In addition to the motherboard and chassis, various hardware components may

have been included with the 1010S-T, as listed below.

One (1) slim ﬂ oppy drive [FPD-PNSC-02(01)]

One (1) slim CD-ROM drive [CDM-TEAC-24(B)]

Two (2) hot-swap SATA drive carriers [(CSE-PT10-(B)]

Two (2) SATA cables (CBL-0044)

One (1) SATA LED cable (CBL-0056)

One (1) air shroud (CSE-PT0113)

Two (2) 4-cm counter-rotating fans (FAN-0087)

One (1) SATA backplane (CSE-SATA-810)

One (1) CPU backplate (BKT-0004)

One (1) heatsink retention module with two (2) screws (BKT-0005)

One (1) PCI-X slot riser card (CSE-RR1U-X)

Rackmount hardware with screws (CSE-PT8)

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

One (1) CD containing drivers and utilities

Chapter 1: Introduction

1-1

Содержание AS-1010S-T





































































































Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды

Supero AS-1010S-T, Руководство пользователя

Результаты поиска

Содержание AS-1010S-T

Отзывы:

Похожие инструкции для AS-1010S-T

Бренды по названию

Популярные бренды