manualshive.com logo in svg

Supermicro SuperBlade SBI-6419P-C3N, Руководство пользователя


Поделиться
Скачать
background image

SBI-6419P-C3N SuperBlade Module User’s Manual

5-6

Table 5-2

 describes all sub-menus found in the A

DVANCED

 S

ETUP

 menu.

Table 5-2. Advanced Setup Menu Options 

Sub-menu

Description

Boot Feature

See 

Table 5-3

 for a description of BIOS setup menu options in this sub-menu.

CPU Configuration

See 

Table 5-4

 for a description of BIOS setup menu options in this sub-menu.

Chipset 

Configuration

See 

Table 5-5

 for a description of BIOS setup menu options in this sub-menu.

Server Me 

Information

See 

Table 5-6

 for a description of BIOS setup menu options in this sub-menu.

SATA Configuration See 

Table 5-7

 for a description of BIOS setup menu options in this sub-menu.

PCIe/PCI/PnP 

Configuration

See 

Table 5-8

 for a description of BIOS setup menu options in this sub-menu.

Super IO 

Configuration

See 

Table 5-9

 for a description of BIOS setup menu options in this sub-menu.

Serial Port Console 

Redirection

See 

Table 5-10

 for a description of BIOS setup menu options in this sub-menu.

ACPI Settings

See 

Table 5-11

 for a description of BIOS setup menu options in this sub-menu.

Trusted Computing

See 

Table 5-12

 for a description of BIOS setup menu options in this sub-menu.

Intel(R) Virtual 

RAID on CPU

See 

Table 5-13

 for a description of BIOS setup menu options in this sub-menu.

Table 5-3. Boot Feature sub-menu 

Menu Option

Description

Quiet Boot

When Disabled the BIOS displays normal POST messages. When 

Enabled

 the BIOS displays an OEM Logo instead of POST messages.

Option ROM Messages

Use this setting to set the display mode for Option ROM to either 

Force 

BIOS

 or Keep Current.

Bootup NUM-Lock State

This setting selects the Power-On state for Numlock. Options include 

On

 

or Off.

Wait for ‘F1’ If Error

When enabled, the system will wait for the F1 key to be pressed if an error 
occurs. Options are 

Enabled

 or Disabled.

Interrupt 19 Capture

When enabled this setting allows option ROMs to trap Interrup 19. Options 
include 

Immediate

 or Postponed.

Re-try Boot

Use this setting to specify the Re-try Boot option to use. Options include 

Disabled

, Legacy Boot or EFI Boot.

Watch Dog Function

This setting allows the system to restart when it is not active more than 5 
minutes. Option include Enabled and 

Disabled

.

Power Button Function

This setting specifies the power button’s function when pressed. Option 
include 4 Seconds Override or

 Instant Off

.

Содержание SuperBlade SBI-6419P-C3N


































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperBlade SBI-6419P-C3N

D-Link DSN-640 Quick Installation Manual preview
DSN-640
Бренд: D-Link Страницы: 40
Canarm MC Series Installation Manual preview
MC Series
Бренд: Canarm Страницы: 3
Bartec MAK 3003 Manual preview
MAK 3003
Бренд: Bartec Страницы: 26
V2 CU1 Manual preview
CU1
Бренд: V2 Страницы: 48
Samson 3430 Operating Instructions Manual preview
3430
Бренд: Samson Страницы: 52
Samson 3275 Mounting And Operating Instructions preview
3275
Бренд: Samson Страницы: 32
Danfoss Cascade Operating Instructions Manual preview
Cascade
Бренд: Danfoss Страницы: 59
Data I/O PSV5000 Operator'S Manual preview
PSV5000
Бренд: Data I/O Страницы: 88
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Бренд: Data Aire Страницы: 13
HABONIM 77 Series Operating Maintenance Installation preview
77 Series
Бренд: HABONIM Страницы: 9
GBD F4 Instructions For Installation Manual preview
F4
Бренд: GBD Страницы: 15
Savant SKL-3040-00 Quick Reference Manual preview
SKL-3040-00
Бренд: Savant Страницы: 2
Gemini GTL5W Instruction Manual preview
GTL5W
Бренд: Gemini Страницы: 9
M-system R7EWTU Instruction Manual preview
R7EWTU
Бренд: M-system Страницы: 18
Xylem Bell & Gossett Technologic PPS Quick Start Manual preview
Bell & Gossett Technologic PPS
Бренд: Xylem Страницы: 20
Toro 53381 Installation Instructions preview
53381
Бренд: Toro Страницы: 2
Halma ZoneSense Plus AS Manual preview
ZoneSense Plus AS
Бренд: Halma Страницы: 58
CAME 001G4040EZT Installation Manual preview
001G4040EZT
Бренд: CAME Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды