manualshive.com logo in svg

Supermicro SuperBlade SBI-6419P-C3N, Руководство пользователя


Поделиться
Скачать
background image

SBI-6419P-C3N SuperBlade Module User’s Manual

1-2

1-3

Blade Module Features

Table 1-1

 lists the main features of the SBI-6419P-C3N blade module. See the 

proceeding section for components typically included in a blade system and other 
optional components. Specific details for the SBI-6419P-C3N blade module are found in 

Chapter 4: "Blade Module Features" on page 4-1

.

Processors

The SBI-6419P-C3N SuperBlade module supports a single Intel Xeon Scalable, Socket 
P LGA 3647 series processor.

Refer to the Supermicro website for a complete listing of supported processors (

http://

www.supermicro.com/products/superblade

). Please note that you will need to check the 

detailed specifications of a particular blade module for a list of the CPUs it supports.

Details on installation of the processor into the SBI-6419P-C3N SuperBlade module are 
found in 

Chapter 3: "Setup and Installation" on page 3-1

.

Memory

The SBI-6419P-C3N SuperBlade module has twelve (12) 288-pin DIMM sockets that 
can support up to 1.5 TB of RDIMM/LRDIMM DDR4 2666/2400 MHz speed, 8 GB, 16 
GB, 32 GB, 64 GB and 128 GB size memory per node. Memory is interleaved, which 
requires modules of the same size and speed to be installed in groups (of two or three). 

Table 1-1. SBI-6419P-C3N SuperBlade Module Specification Features

Mainboard

B11SPE-CPU-TF/25G (proprietary form factor)

Processors

Dual Intel

™

 Xeon

®

 Scalable Socket P LGA3647 processors for each node. 

Please refer to our website for a complete listing of supported processors.

UPI Speed

UPI up to 10.4 GT/s

Chipset

One Intel C622 chip set

Graphics Controller

Integrated Aspeed AST2500 VGA Graphics chip for each node

BIOS

128 Mb SPI Flash EEPROM with AMI® BIOS for each node

Memory Capacity

Supports up to 1.5 TB of RDIMM/LRDIMM DDR4 2666/2400 MHz speed and 8 
GB, 16 GB, 32 GB, 64 GB and 128 GB size memory in twelve (12) 288-pin 
DIMM sockets. See 

https://www.supermicro.com/support/resources/memory/

X11_memory_config_guide.pdf

 for details.

Hard Drive Bays

Includes two hot-swap 2.5" NVMe disk drives plus one hot-swap 2.5" SAS3/
SATA3 drive or three 2.5" SAS3/SATA3 drives

Add-on Cards

The SBI-6419P-C3N blade module can use optional add-on cards for a TPM 
security module, Intel VROC RAID card or a Hardware RSTe key upgrade 
module.

System Weight 

10.5 lbs (4.76 kg)

System Dimensions

(HxWxD): 9.76 x 1.75 x 23.5” (247.9 x 44.45 x 596.9-mm)

Содержание SuperBlade SBI-6419P-C3N


































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperBlade SBI-6419P-C3N

GE RSTi-EP User Manual preview
RSTi-EP
Бренд: GE Страницы: 425
A10 Harmony Controller 2000 Installation Manual preview
Harmony Controller 2000
Бренд: A10 Страницы: 27
Saga SAGA1-L40 User Manual preview
SAGA1-L40
Бренд: Saga Страницы: 9
Absima CR9T Quick Start preview
CR9T
Бренд: Absima Страницы: 5
WAGNER 2K COMFORT Original Operating Manual preview
2K COMFORT
Бренд: WAGNER Страницы: 128
Novax IntelliCross TouchFree Kit Installation Manual preview
IntelliCross TouchFree Kit
Бренд: Novax Страницы: 3
Daikin BRC51D64 Operating Manual preview
BRC51D64
Бренд: Daikin Страницы: 19
AUMA GSTI 25.1 Operating Instructions Manual preview
GSTI 25.1
Бренд: AUMA Страницы: 24
VALSTEAM ADCA TSS 7 Installation And Maintenance Instructions preview
TSS 7
Бренд: VALSTEAM ADCA Страницы: 4
MT-Propeller P-8S Series Operation And Installation Manual preview
P-8S Series
Бренд: MT-Propeller Страницы: 16
ICP DAS USA ET-7083 Quick Start Manual preview
ET-7083
Бренд: ICP DAS USA Страницы: 8
WAGO 750-528 Manual preview
750-528
Бренд: WAGO Страницы: 50
V2 FORTECO 2500-I Manual preview
FORTECO 2500-I
Бренд: V2 Страницы: 108
Omega Engineering Series RHCN-7000 Install And Operation Instructions preview
Series RHCN-7000
Бренд: Omega Engineering Страницы: 2
Eaton xComfort CHSZ-12/03 Instruction Leaflet preview
xComfort CHSZ-12/03
Бренд: Eaton Страницы: 4
WAM MIC 23 Assembly Instructions preview
MIC 23
Бренд: WAM Страницы: 2
Zamel NC60 Quick Manual preview
NC60
Бренд: Zamel Страницы: 2
Texecom Veritas R8 Plus User Manual preview
Veritas R8 Plus
Бренд: Texecom Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды