Supermicro SuperBlade SBI-6419P-C3N Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 97

background image

iii

:

Preface

About this Manual

This manual is written for professional system integrators, Information Technology
professionals, service personnel and technicians. It provides information for the
installation and use of the Supermicro SuperBlade

®

system’s SBI-6419P-C3N

SuperBlade module. Installation and maintenance should be performed by experienced
professionals only.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with
SBI-6419P-C3N SuperBlade module and describes their main features.

Chapter 2: System Safety

You should familiarize yourself with this chapter for a general overview of safety
precautions that should be followed when installing and servicing SBI-6419P-C3N
SuperBlade module.

Chapter 3: Setup and Installation

Refer to this chapter for details on installing the SBI-6419P-C3N SuperBlade module
into the SuperBlade chassis. Other sections cover the installation and placement of
memory modules and the installation of hard disk drives into the blade module.

Chapter 4: Blade Module Features

This chapter coves features and component information about SBI-6419P-C3N
SuperBlade module. Included here are descriptions and information for mainboard
components, connectors, LEDs and other features of the blade module.

Chapter 5: BIOS

BIOS setup is covered in this chapter for SBI-6419P-C3N SuperBlade module.

Appendix A: BIOS POST Codes

BIOS POST Codes for SBI-6419P-C3N SuperBlade module are explained in this
appendix.

«
1
2
3
4
5
...
»

Содержание SuperBlade SBI-6419P-C3N


































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Haldex Страницы: 8

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: RADEMACHER Страницы: 48

Бренд: D+H Страницы: 32

Бренд: OEM Страницы: 8

Бренд: ABB Страницы: 102

Бренд: DSE Страницы: 2

Бренд: National Instruments Страницы: 14

Pearldex Series

Бренд: KaMo Страницы: 2

Бренд: Wavelength Electronics Страницы: 17

Бренд: UUGear Страницы: 38

Бренд: HTW Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды