Supermicro SuperBlade SBI-6419P-C3N Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 97

background image

SBI-6419P-C3N SuperBlade Module User’s Manual

3-10

Preparing the CPU Socket for Installation

This motherboard comes with the CPU socket pre-assembled in the factory. The CPU
socket contains 1) a dust cover, 2) a socket bracket, 3) the CPU (P0) socket, and 4) a
back plate. These components are pre-installed on the motherboard before shipping.

Removing the Dust Cover from the CPU Socket

Remove the dust cover from the CPU socket, exposing the socket and socket pins as
shown on the illustration below.

Note:

Do not touch the socket pins to avoid damaging them, causing the CPU to

malfunction.

CPU Socket w/Dust Cover On

Socket Pins

Remove the dust cover from

the CPU socket. Do not

touch the socket pins!

«
...
38
39
40
41
42
...
»

Содержание SuperBlade SBI-6419P-C3N


































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренд: MADRIX Страницы: 36

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Бренд: Parker Страницы: 44

Бренд: Watts Страницы: 4

Бренд: DAQ Страницы: 63

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

F&G Xcomfort CRCA-00/02

Бренд: Moeller Страницы: 4

Бренд: Pfeiffer Vacuum Страницы: 100

Бренд: Objective Imaging Страницы: 11

Бренд: Dickey-John Страницы: 109

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: SILENTRON Страницы: 20

Бренд: MacroAir Technologies Страницы: 32

Бренд: McIntosh Страницы: 68

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды