Supermicro SuperBlade SBI-6419P-C3N Скачать руководство пользователя страница 32

Страница: 32 / 97

SBI-6419P-C3N SuperBlade Module User’s Manual

3-2

Removing a Blade Unit from the Enclosure

Although the blade system may continue to run, individual blades should always be
powered down before removing them from the enclosure.

Removing a Blade Unit from the Enclosure

Power down the blade unit (see

"Powering Down a Blade Unit"

above).

Squeeze the handle to depress the red section then pull out the blade unit from the
enclosure using the handle.

Note:

Blade Modules can be Hot-Plugged from the enclosure.

Installing a Blade Unit into the Enclosure

Slowly push the blade unit into its bay with the handles fully pulled out (see

Figure 3-1

When the blade stops, push the handle back into its locked position, making sure
the notches in the handle catches the lip of the enclosure (see

Figure 3-3

Note:

Blade Modules can be Hot-Plugged into the enclosure.

Caution: Use extreme caution when inserting a blade module into the enclosure

. If the

blade's power connector becomes damaged, it can damage pins on other blade bays that it
is inserted into.

Содержание SuperBlade SBI-6419P-C3N


































































































Результаты поиска

Содержание SuperBlade SBI-6419P-C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренды по названию

Популярные бренды

Supermicro SuperBlade SBI-6419P-C3N, Руководство пользователя

Результаты поиска

Содержание SuperBlade SBI-6419P-C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренды по названию

Популярные бренды