Supermicro SuperBlade SBI-6419P-C3N Скачать руководство пользователя страница 70

Страница: 70 / 97

SBI-6419P-C3N SuperBlade Module User’s Manual

5-10

MCP1 (IIO PCIe
Br5)

This setting selects the PCIe port bifurcation for Br5. Options include x16
or

Auto



Socket 0

PcieBr0D00F0 -
Port 0/DMI ~
Socket 0
PcieBr5D00F0 -
MCP 1 Submenu

Settings for these submenus are related to PCI Express Ports in your
system. This submenu contains a mix of static information and
configurable option settings.

Link Speed

This setting specifies the link speed for the PCI-E port. Options include

Auto

, Gen 1 (2.5 GT/s), Gen 2 (5 GT/s) and Gen 3 (8GT/s)

PCI-E Port
Max Payload
Size

This sets the max payload size. Options include 128B, 256B or

Auto

ECRC

This setting Enables or

Disables

ECRC (Error Capabilities and Control



IOAT

Configuration

This submenu allows you to configure IOUT configuration options.

Disable TPH

This setting lets you turn on/off TLP Processing Hint disabling. Options are
Yes or

Prioritize TPH

This setting allows you to Enable or

Disable

the Prioritize TPH option.

Relaxed
Ordering

This setting Enables or

Disables

relaxed ordering in your system.



Intel VT for

Directed I/O (VT-d)

Use this submenu to bring up options for Intel VT for Directed I/O
configurations.

Intel VT for
Directed I/O
(VT-d)

This setting allows you to

Enable

or Disable Intel Virtualization Technology

for Directed I/O (VT-d) by reporting the I/O device assignment to VMM
through the DMAR ACPI Tables.

Interrupt
Remapping

This setting allows you to

Enable

or Disable the VT_D Interrupt

Remapping support.

Passthrough
DMA

This setting allows you to

Enable

or Disable the Non-Isoch VT_D Engine

Pass Through DMA support.

ATS

This setting allows you to

Enable

or Disable the Non-Isoch VT_D Engine

ATS support.

Posted Interrupt

This setting allows you to

Enable

or Disable the VT_D Posted Interrupt.

Coherency
Support
(Non-Isoch)

This setting allows you to

Enable

or Disable the VT_D Engine Coherency

support.

PCIe Hot Plug

This setting allows you to Enable/Disable PCIe Hot Plug globally. Options
include

Disable

, Enable, Auto and Manual.

PCI-E Completion
Timeout (Global)

This setting allows you to Enable/Disable the Completion Timeout, where x
is 0-3. Options include Yes,

and Per-Port.



South Bridge

Configuration

This sub-menu allows you to configure South Bridge parameters.

Table 5-5. Chipset Configuration Sub-menu (Continued)

Menu Option

Description

Содержание SuperBlade SBI-6419P-C3N


































































































Результаты поиска

Содержание SuperBlade SBI-6419P-C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренды по названию

Популярные бренды

Supermicro SuperBlade SBI-6419P-C3N, Руководство пользователя

Результаты поиска

Содержание SuperBlade SBI-6419P-C3N

Отзывы:

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренды по названию

Популярные бренды