Stratasys 180-00108 uPrint Скачать руководство пользователя страница 59

Страница: 59 / 68

Stratasys Document Number 206465-0001

Troubleshooting and Maintenance

Extrusion Tip Replacement and Calibration

Replace Tips at approximately 2000 hours.

Note:

Tips can also be damaged by improper care while performing
maintenance in the area around the tips.

CatalystEX displays the tip time (hrs) - from the Printer Services
Tab - Printer Info button (Tip time will reset to zero after
replacement).

Removing Tips:

1. You will need to make sure the printer is powered ON before replacing the extrusion tips.

2. From the display panel press

Maintenance

3. Press

Machine

4. Press

Tip

5. The printer will display

Load Model - Unloading

6. After the temperature has stabilized, the printer will display

Tip Maintenance - Replace Tips

. You can

now open the printer door and replace the tips - or you can

Cancel

the tip replacement procedure.

7. Remove plastic head cover by squeezing raised pads on sides of cover.

Figure 38: Removing the Head Cover

8. Remove Tips

A. Use 7/64 T-Handle Allen wrench to loosen the tip screws three to four full turns counterclockwise -

or until the top of the screws are flush with the metal cover. DO NOT remove the screws entirely.
See

Figure 39.

Press clips in and pull head cover out

Содержание 180-00108 uPrint





































































Результаты поиска

Содержание 180-00108 uPrint

Отзывы:

Stratasys 180-00108 uPrint, Руководство пользователя, Страница: 59 / 68

Результаты поиска

Содержание 180-00108 uPrint

Отзывы: