Stratasys 180-00108 uPrint Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 68

Stratasys 180-00108 uPrint Скачать руководство пользователя страница 29

Stratasys Document Number 206465-0001

Setup

29

System Software

The system software is factory loaded on the printer. Due to occasional changes you may need to update
the printer system software.

Updating System Software:

1. From the

uPrint

display panel, press

Maintenance

.

2. Press

System

.

3. Press

Load Upgrade

. The printer will then display

“Send upgrade from workstation”

followed by

the printer’s IP Address.

4. Open CatalystEX and click on the

Printer Services

tab.

5. Click on the

Update Software

button. CatalystEX will now connect to the printer and will prompt you to

locate the upgrade file. Direct the software to the CD the upgrade file is on. The update will automati-
cally be loaded on to the printer. After the update has been loaded, the display will show

Verifying

update

.

6. When the verification has completed, the display will show

Reboot to complete

. Select

Yes

. The

printer will now reboot and return to

Idle

.

Press the maintenance button and verify the updated version was installed correctly.

Installing a spool of material into the material carriers

An instructional video can be viewed at

http://www.uPrintDimension.com

Installing a spool of material into the carrier:

1. For new carriers, remove the carrier from shipping box. Place on a flat surface, unlatch and open. See

Figure 17

.

Note:

Save the enclosed storage bag for later use. The storage bag will
be used to store material spools when they are not in use, and
will help keep moisture out of the material.

Figure 17: Opening the carrier

2. Remove the material spool from the shipping box. Tear open the bag and discard (the bag will have a

notch for tearing open). Note how the material and material guide are held in place under a clear mate-
rial retaining band. See

Figure 18

.

Push in

Pull out

«
...
27
28
29
30
31
...
»

Содержание 180-00108 uPrint





































































Отзывы:

Нет отзывов