manualshive.com logo in svg

Stratasys 180-00108 uPrint, Руководство пользователя, Страница: 53 / 68

Поделиться
Скачать
Stratasys 180-00108 uPrint Скачать руководство пользователя страница 53

Stratasys Document Number 206465-0001

Troubleshooting and Maintenance

53

11. After approximately 5 seconds, reduce pressure against the toggle spring and allow the idler wheel to 

contact the material. Material should extrude from the clogged tip. 

Note:

The blower will automatically turn on in 10 seconds.

12. Press 

Stop

 on the interface panel.

13. Move the toggle bar to activate the drive wheel control options for the non-clogged side.

14. Press 

Forward

 on the interface panel. Make sure that material extrudes from the non-clogged extru-

sion tip.

Note:

It is necessary to confirm proper operation of the non-clogged 
side. Temporarily having the blower off can occasionally cause 
the non-clogged side to clog.

15. Press 

Stop

 on the interface panel.

16. Install plastic head cover.

17. Exit Maintenance mode. 

Recovering From Loss of Extrusion

Note:

It is recommended that you read and understand this entire 
procedure before performing any of the work.

1.  Enter 

Head Maintenance

 mode.

A.   From 

Idle

, press 

Maintenance

.

B. Press 

Next

.

C. Press 

Head Maintenance

.

2. Remove plastic head cover.

•

Remove plastic head cover by squeezing raised pads on sides of cover. See 

Figure 38

.

3. Place the tip toggle bar in neutral position (bar will extend equally from both sides of head). This can be 

done manually - push on the extended bar end.

WARNING

The head area is hot. Use leather gloves when working in this area of printer. 

Содержание 180-00108 uPrint





































































Отзывы:

Нет отзывов