STM SatLink Скачать руководство пользователя страница 9

Страница: 9 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 9

3.2

SatLink Terminal front and back panels

3.2.1 SatLink 1000 front and back panel

Figure 3: SatLink 1000 Front panel

LED

Colour, indicates

Power

Blue, lights steadily when power switch is on and unit is powered. Flashes when loading

software.

Error

Red, lights steadily when an error event occurs and during reboot.

Satellite

Receive

Blue, flashes when the receiver is searching for the carrier.

Lights steadily when receiver is on and functioning properly.

Flashes when IP packets are received from the Satellite Interface (the Gateway).

Transmit

Blue, flashes rapidly when a continuous wave (CW) is transmitted.

Lights steadily when the terminal is logged on to the DVB-RCS gateway.

Flashes when IP packets are transmitted to the Satellite Interface (the Gateway).

Ethernet Link/Act

Blue, lights steadily when Ethernet connectivity is OK.

Flashes slowly when Ethernet packets are transferred via the Ethernet interface.

Table 1: SatLink 1000 front-panel LEDs

Figure 4: SatLink 1000 back panel

Item

Description

On/off switch

Mains power on (1) or off (0).

Mains Connector

Connector for cable to the 24 V DC power transformer (external power supply provided

with STM SatLink 1000 Terminal)

Ethernet

Connector

RJ45 connector for IP traffic to connect to a PC, Ethernet switch, IP router etc. 10BASE-T

or 100BASE-T modes are detected automatically.

COM1 Connector

Nine-pin connector for connecting CLI interface to a computer serial RS232 interface.

Rx coaxial jack

Coaxial 75

Ω

F-type jack for the cable to the LNB.

Tx coaxial jack

Coaxial 75

Ω

F-type jack for the cable to the BUC.

Table 2: SatLink 1000 back panel description

Содержание SatLink











































































































Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды

STM SatLink, Руководство пользователя

Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды