STM SatLink Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 110

background image

Copyright © 2006 – STM Norway AS

Publication no. 101557, Rev. T, November 3

th

, 2006

Page 59

When the card has been detected by the terminal, the DVB-S2 is configured the same was as DVB-S.

described in section 6.2.4.

Example:

# dvb rx fwdlink 0 0 25000000 12380000 dvbs2 2
# save config
# dvb rx show

Satellite (DVB) RX Configuration
--------------------------------
Auto start          : Disabled

Idx  Pri  Freq[GHz]  SymbRate[Msps]  Mode   PopId
* 0    0  12.380000  25.000000       DVB-S2   2

DVB Receiver Status (SatLink 100)
--------------------------------
Rx State            : Waiting for NIT (transponder one)
Frequency           : 12.380887 GHz
Symbol Rate         : 24.999998 Msps
Modulation          : 8PSK
FEC Code rate       : 2/3
Pilot               : On
Frame length        : Long frame
Roll off            : 0.35
SNR                 : 15.2 dB

For V2 of the STM SatLink 1910 and 1000 IDU, there is no need for the SatLink 100 extension card.

Both types are configured the same way as the example shows above.

«
...
57
58
59
60
61
...
»

Содержание SatLink















































































































Отзывы:

Нет отзывов

Похожие инструкции для SatLink

Бренд: Equinox Systems Страницы: 12

Бренд: HANTEL Страницы: 105

Бренд: XtendLan Страницы: 70

Harbortouch iPP320

Бренд: SHIFT4 Страницы: 13

First Data A920

Бренд: Fiserv Страницы: 6

Бренд: ZK Страницы: 36

Бренд: ZK Technology Страницы: 46

Бренд: uAccept Страницы: 11

Бренд: ELTEX Страницы: 299

FieldPoint FP-TB-10

Бренд: National Instruments Страницы: 22

Бренд: FSP Technology Страницы: 21

Бренд: Datafox Страницы: 135

Бренд: Custom Audio Electronics Страницы: 20

Бренд: Custom Audio Electronics Страницы: 32

CartStop FlexCore Post 3

Бренд: McCue Страницы: 6

Бренд: FaceID Страницы: 36

Бренд: Hisense Страницы: 41

Бренд: Dahua Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды