STM SatLink Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 110

background image

Copyright © 2006 – STM Norway AS

Publication no. 101557, Rev. T, November 3

th

, 2006

Page 51

If the Header compression is not available on the GW, the

DVB TX SHOW

command will display these

values:

# dvb tx show

Satellite (DVB) TX Configuration
--------------------------------
Auto start          : Enabled
Population ID       : 2
IDU output power    : -23 dBm
EIRP                : max
Default CW Frequency: 14.488000 GHz
ATM mode            : VC-Mux

Header Compression : UDP/IP/DSM-CC

DVB Transmitter Status
--------------------------------
State : On

Header Compression : Disabled

IDU Output Power    : -22.9 dBm
Eb/No               : 13.5 dB
Timing correction   : 2605 us
Frequency correction: 70 Hz

11.2 Disable Header compression

To disable the Header Compression, use the same set of commands, as used when it was enabled, but

with a ‘–‘ instead of a ‘+’.

# dvb hdrcomp -dsmcc
# dvb hdrcomp -udp
# dvb tx show

Satellite (DVB) TX Configuration
--------------------------------
Auto start          : Enabled
Population ID       : 2
IDU output power    : -23 dBm
EIRP                : max
Default CW Frequency: 14.488000 GHz
ATM mode            : VC-Mux

Header Compression : None

DVB Transmitter Status
--------------------------------
State : On

Header Compression : Disabled

IDU Output Power    : -22.9 dBm
Eb/No               : 13.5 dB
Timing correction   : 2605 us
Frequency correction: 70 Hz

«
...
49
50
51
52
53
...
»

Содержание SatLink















































































































Отзывы:

Нет отзывов

Похожие инструкции для SatLink

Бренд: IBM Страницы: 74

Бренд: IBM Страницы: 207

MorphoAccess SIGMA Lite Series

Бренд: Idemia Страницы: 32

Бренд: Union Community Страницы: 28

Бренд: AURES Страницы: 79

Бренд: RusGuard Страницы: 20

Бренд: D-Link Страницы: 61

Бренд: Burnside Страницы: 2

HTK Pay Station

Бренд: Hamilton Страницы: 36

Бренд: IVC Displays Страницы: 30

Бренд: CommScope Страницы: 11

Бренд: Newland Страницы: 44

Бренд: NetPay Страницы: 30

Бренд: NCR Страницы: 244

Бренд: NCR Страницы: 100

Бренд: TD Страницы: 32

Бренд: Partner Страницы: 2

Бренд: Partner Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды