STM SatLink Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 110

background image

Copyright © 2006 – STM Norway AS

Publication no. 101557, Rev. T, November 3

th

, 2006

Page 35

9.

Issue the CLI command

dvb tx calibrate

to start the automatic transmitter power calibration

routine. During this calibration, the transmit EIRP level is detected and the IDU output level is

automatically adjusted to the level required for transmitting with the configured EIRP level. Hence no

manual configuration of the IDU output power level or cable attenuation is required.

Ask the control centre if they can detect the transmitted CW. If they are not able to

see the CW at the specified frequency and expected output power level, please power

off the STM SatLink Terminal immediately.

Example:

# dvb tx calibrate
Using preconfigured CW frequency 14.488000 GHz
RF Wanted=  30.7, RF Measured=   0.0, If output= -30.1
RF Wanted=  30.7, RF Measured=  30.6, If output= -26.6
ODU output level stabilised
Saving configuration

Note: CW transmission is still enabled to allow
      for crosspolarisation adjustment of the antenna

Configuration Saved

10.

Verify the calibrated power levels using the CLI command

dvb tx show

.

Example:

dvb tx show

Satellite (DVB) TX Configuration
--------------------------------
Auto start          : Enabled
Population ID       : 2
IDU output power    : -11 dBm
EIRP                : max
Default CW Frequency: 14.488000 GHz
AAL5 Encapsulation  : VC MUX

DVB Transmitter Status
----------------------
State                 : On
IDU Output Power      : -13.6 dBm
ODU Output Power      : 33.2 dBm
EIRP                  : 46.5 dBW
delta T               : 263366 microseconds
Frequency Correction  : -2650 Hz
#

Leave the CW on for fine adjustment of the antenna, or turn it off using the CLI command

dvb tx cw off

.

6.3.3 Fine adjustment of antenna pointing

If the CW from the power calibration routine is still on, it can be used for the antenna fine-adjustment as

well. Otherwise start CW transmission on the default CW frequency by issuing the CLI command

dvb

tx cw on.

«
...
33
34
35
36
37
...
»

Содержание SatLink















































































































Отзывы:

Нет отзывов

Похожие инструкции для SatLink

Бренд: Partner Страницы: 50

Бренд: Union Community Страницы: 28

AKI-CDC-MOD-15T

Бренд: Kollmorgen Страницы: 36

Бренд: AURES Страницы: 79

XpressNet Digital plus LA152

Бренд: Lenz Страницы: 2

Бренд: SAND Страницы: 25

CINTERION BGS2T

Бренд: Gemalto Страницы: 554

Бренд: Omron Страницы: 2

Бренд: NetPay Страницы: 30

Бренд: WideFly Страницы: 16

Бренд: Ingenico group Страницы: 16

VIPA TP-ECO TP 604LC

Бренд: YASKAWA Страницы: 75

morphoaccess sigma lite

Бренд: Safran Страницы: 32

MorphoAccess J-Bio

Бренд: Sagem Securite Страницы: 118

Бренд: IBM Страницы: 60

Бренд: PAR Страницы: 11

Бренд: Magtek Страницы: 22

SPT-7000 Series

Бренд: Sam4s Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды