STM SatLink Скачать руководство пользователя страница 83

Страница: 83 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 83

When mounting the transceiver to the antenna horn, place the feed horn on a level surface and insert the

O-ring supplied with the antenna feed horn into the groove as shown below:

Figure 21: Inserting O-ring into feed horn groove

Place the transceiver on to the feed horn and insert one of the UNC screws for alignment. Tighten the

screw loosely by hand or with an Allen key. Make sure that the rubber gasket is not removed from the

groove when doing this.

Figure 22: Mounting feed horn

Insert the remaining screws and tighten firmly with an Allen key. Always use screws from mounting kit

supplied with the STM SatLink 4033/4035 (part no. 105773). Do not use other screws or apply washers!

Содержание SatLink











































































































Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды

STM SatLink, Руководство пользователя

Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды