STM SatLink Скачать руководство пользователя страница 38

Страница: 38 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 38

To test the IP connection to the gateway open an MS-DOS window on the PC connected to the STM

SatLink Terminal LAN (Ethernet).

Type the MS-DOS command ‘ping 10.10.10.1’ to test the connection to the gateway router

If the router gives a positive reply to the ping message then the DVB-RCS satellite link is

successfully up and running.

To test the connection to the Internet, type the MS-DOS command ‘ping www.stmnetworks.com’. If

a reply is received the PC connected to the STM SatLink Terminal has a working connection to the

Internet via the DVB-RCS satellite network.

6.5

Prepare the STM SatLink Terminal for normal operation

The connection to the Internet over the DVB-RCS satellite network should now be tested and found

working. The only thing left is then the final configuration to prepare the STM SatLink Terminal for

normal operation.

The STM SatLink Terminal must be started and you must be logged in as a user with minimum privilege

level 2 (e.g.

install

user) before completing the following operations.

Configure the STM SatLink Terminal to automatically start the receiver by typing the CLI command

dvb rx autostart on

Setting the Rx autostart on will ensure that the receiver is started automatically after e.g. power

failure, link failure, gateway restart, or a software failure, etc. without needing user intervention.

Verify that auto start is on for the receiver by typing the CLI command

dvb rx show

Configure the STM SatLink Terminal to automatically start the transmitter by typing the CLI

command

dvb tx autostart on

Setting the Tx autostart on will ensure that the transmitter is started automatically after e.g. power

failure, link failure, gateway restart, or a software failure, etc. without needing user intervention.

Or alternatively follow the procedure in section 10 if the terminal shall use traffic-initiated logon.

Verify that auto start is on for the transmitter by typing the CLI command

dvb tx show

Save the configuration by typing the CLI command

save config

Replace the IP address 10.10.10.1 with the actual IP address of the DVB-RCS gateway router if the

default IP configuration of the DVB-RCS gateway is not used.

Содержание SatLink











































































































Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды

STM SatLink, Руководство пользователя

Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды