STM SatLink Скачать руководство пользователя страница 90

Страница: 90 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 90

Appendix I.

STM SatLink 403x. Interfacing VSAT RX/TX

antennas

The STM SatLink 403x series of Ku-band transceivers is configured with internal OMT as shown in

Figure 27 below. The output interface of the transceiver (C120) is therefore connected directly to the feed

horn of the antenna.

Figure 27: STM SatLink 403x output interface (Option A)

Antenna vendors offer different variants of the feed horn for their Ku-band RX/TX

antennas. The different options are listed below.

Option

Feed Horn Interface

C120 – 6 UNC screws

C120 – 6 or 8 M4 screws

Option A interfaces the STM SatLink 403x directly while Option B requires an adaptor in order to fit the

STM SatLink 403x output interface. The hole patterns for option A and B are shown in Figure 28 and

Figure 29.

Figure 28: Option A antenna feed

hole pattern. Holes are distributed

equally at 60 degrees apart. STM

SatLink 403x fits directly to this

pattern using 6 UNC screws for

fastening.

Figure 29: Option B antenna feed hole pattern. Holes are

equally distributed at 45 degrees apart. Some versions have

only 6 holes. STM SatLink 403x fits on this pattern by means

of adapter STM SatLink 4901 (STM P/N 107268).

Содержание SatLink











































































































Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды

STM SatLink, Руководство пользователя

Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды