STM SatLink Скачать руководство пользователя страница 17

Страница: 17 / 110

Publication no. 101557, Rev. T, November 3

, 2006

Page 17

4.1.2 Static IP configuration of PCs connected to the STM SatLink Terminal LAN

When the DHCP server in the SatLink Terminal is disabled, all PCs attached to the STM SatLink

Terminal LAN must be configured with static IP addresses that are within range of the STM SatLink

Terminal subnet (see section 6.2.1). The IP configuration parameters to use for PCs connected to the STM

SatLink Terminal LAN are supplied from the system operator or service provider. Please configure the IP

address, Subnet mask, Default gateway, Preferred DNS server, and optionally the Alternate DNS server

as shown in Figure 13.

Ensure that the actual IP addresses supplied by the system operator / service provider are

configured and not the IP addresses in the example figure.

Figure 13: Windows XP TCP/IP setting when DHCP server is disabled in the Terminal

Example:

A host may have the following configuration; IP address 192.168.0.2, Subnet mask 255.255.255.0 and

default gateway 192.168.0.1, where the IP address of the default gateway should be the IP address of the

STM SatLink Terminal LAN interface.

Содержание SatLink











































































































Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды

STM SatLink, Руководство пользователя

Результаты поиска

Содержание SatLink

Отзывы:

Похожие инструкции для SatLink

Бренды по названию

Популярные бренды