CPF180i and CPF300i
Page 23
CPF180i
Battery
1
0-
3
5Vdc
R
ed
2
A
Fuse
Black
S
witch
+
-
VHF
PILOT
G
reen
Blue
Brown
NMEA Co
mm
on
P
ort
1
Input
P
ort
1 O
utput
Yellow
P
ort
3 O
utput
PWR & ACC 1 Cable
Transducer
Optional WAAS GPS
antenna
2.4.1.2 AIS Setup
The CPF180i has to be set up to be able to receive NMEA information from the AIS receiver.
The GPS Chart Plotter reads the AIS NMEA message VMD, type 1, 2, 3 and 5 for AIS Class
A and type 18, 19, 24 for AIS Class B. Select the used port and transmission speed by
following the procedure:
1. Press
[MENU]
, move the ShuttlePoint knob to highlight
SETUP MENU
and press
[ENT]
.
2. Move the ShuttlePoint knob to highlight
ADVANCED SETUP
and press
[ENT]
or move
the ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight
IN/OUT CONNECTIONS
and press
[ENT]
or
move the ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight
PORT1 INPUT
and press
[ENT]
or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up/down to select
AIS 38400
and press
[ENT]
or move the
ShuttlePoint knob to the right.
NOTE
If an AIS receiver is not connected, Port1 Input can be connected to most DSC VHF’s for position polling.
NOTE
The Input and Output baud rate for each port is set using the Advanced Setup>In/Out Connections
menu. For example if Port1 is set for AIS 38400, the Input and Output both operate at 38400 baud.
2.4.2 CPF300i Connection Table
12VDC Power
Pin Wire Color Description
Connection Example
Additional Comments
1
Black
Battery Ground &
Connect to Battery Ground and
Common for
and signal ground
NMEA devices*
2
Red
Battery Positive
Connect to Battery Positive
3
Green
Port3 Input
Connect to Output of NMEA devices*
Default is NMEA0183
4
Blue
Port1 Input
Connect to Output of NMEA devices*
Default is NMEA0183
5
Brown
Port1 Output
Connect to Input of NMEA devices*
Default is NMEA0183 with GGA, GLL, RMC,
XTE, DBT, DPT, MTW, VHW sentences
6
Gray
Port2 Input
Connect to Output of NMEA devices*
Default is NMEA0183
7
White
Port2 Output
Connect to Input of NMEA devices*
Default is NMEA0183 with GGA, GLL, RMC
and XTE sentences
8
Yellow
Port3 Output
Connect to Input of NMEA devices*
Default is NMEA0183 with APA, APB, BOD,
GGA, GLL, RMC and BOD sentences
Содержание CPF180I
