SPRT SP-T8 Скачать руководство пользователя страница 98

Страница: 98 / 125

by nL and nH.



The printing area width is set to [( nL + nH



256)



horizontal motion unit)]

inches.

Printable area

[Notes]



This command is effective only processed at the beginning

of the line.



n page mode, the printer performs only internal flag

operations.



This command does not affect printing in page mode.



If the [left printing area width] exceeds the

printable area, [printable area width - left margin) is used.



The horizontal a

nd vertical motion units are specified by

GS P

. Changing the horizontal and vertical motion units does

not affect the current left margin.



The horizontal motion unit is used for calculating the

printing area width. The calculated result is truncated to the
minimum value of the mechanical pitch.
[Default] nL = 76, nH = 2
[Reference]

GS L

GS P

Содержание SP-T8






























































































































Результаты поиска

Содержание SP-T8

Отзывы:

Бренды по названию

Популярные бренды

SPRT SP-T8, Руководство пользователя

Результаты поиска

Содержание SP-T8

Отзывы:

Бренды по названию

Популярные бренды