SPRT SP-T8 Скачать руководство пользователя страница 93

Страница: 93 / 125

depending on the receive buffer status.



When the printer ID transmission is specified with (1



3) or (49



51),one byte code is tr

ansmitted.



When Auto Status Back (ASB) is enabled using

GS a

, the

status transmitted by

I and the ASB status must be

differentiated.



After the data is ready to be transmitted, the printer

executes the following process.



When the printer ID transmi

ssion is specified with (65



69), the following contents are transmitted:

Header: Hexadecimal = 5FH / Decimal = 95 (1 byte)
Data: Printer information
NUL: Hexadecimal = 00H / Decimal = 0 (1 byte)



Executes READY to BUSY. If it is already BUSY, the

①

printer executes nothing.



Transmits [ Data + NUL].

②



Executes BUSY to READY. If it is already BUSY from any

③

other cause, the printer executes nothing.

GS L nL nH

[Name] Set left margin
[Format] ASCII GS L nL nH

Hex 1D 4C nL nH
Decimal 29 76 nL nH

[Range] 0



255; 0



255

[Description] Sets the left margin using nL and nH.

Содержание SP-T8






























































































































Результаты поиска

Содержание SP-T8

Отзывы:

Бренды по названию

Популярные бренды

SPRT SP-T8, Руководство пользователя

Результаты поиска

Содержание SP-T8

Отзывы:

Бренды по названию

Популярные бренды