manualshive.com logo in svg

SPRT SP-T8, Руководство пользователя

Поделиться
Скачать
SPRT SP-T8 Скачать руководство пользователя страница 60

 

60

If this command is input in standard mode, the printer

　

   

executes only internal flag operation. This command does   
not affect printing in standard mode. 

If the horizontal or vertical starting position is set outside 

　

the printable area, the printer stops command processing 
and processes the following data as normal data. 

If the printing area width or height is set to 0, the printer 

　

stops command processing and processes the following data 
as normal data. 

This command sets the position where data is buffered to 

　

the position specified by 

ESC T 

within the printing area. 

If (horizontal starting po printing area width) 

　

exceeds the printable area, the printing area width is 
automatically set to (horizontal printable area- horizontal 
starting position). 

If (vertical starting po printing area he

　

ight) exceeds 

the printable area, the printing area height is automatically 
set to (vertical printable area – vertical starting position). 

The horizontal and vertical motion unit are specified by 

　

GS 

P

. Changing the horizontal or vertical motion unit does not 

affect the current printing area. 

The 

　

GS P 

command can change the horizontal (and 

vertical) motion unit. However, the value cannot be less than 
the minimum horizontal movement amount, and it must be in 
even units of minimum horizontal movement amount. 

Use the horizontal motion unit ( x) for setting the horizontal 

　

Содержание SP-T8






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды