Sony MSB-2000 Скачать руководство пользователя | Manualshive

Страница: 92 / 113

background image

92

Simple Network Management Protocol (SNMP)

(21) snmp trap select command [enable/disable]

Sets/Unsets MSB-2000/MSBA-20IP commands as
a trap.
This command is available when the trap switch is
set to enable_select.
This command is resumed.

(22) snmp trap select status [enable/disable]

Sets/Unsets MSB-2000/MSBA-20IP status as a
trap.
This command is available when the switch is set
to enable_select.
This command is resumed.

(23) snmp trap select summary [enable/disable]

Sets whether or not to output a summary trap.
This command is resumed.
If the argument is omitted, the error message
“invalid parameter” is returned.

Note

A “summary trap” refers to the following seven
logs.
• 30030035 Status SDI/SDTI input present/absent
• 30030036 Status ASI input present/absent
• 30030076 Status --- Tx is up ---
• 30030077 Status --- Rx is up ---
• 30030073 Status RTP link status up/down
• 12053010 Picture Freeze (Rx)
• 10053010 Picture Freeze (Rx) (CLEAR)
The following specific example settings output the
above seven traps only within the status log, minor
log, and clear minor log:

snmp trap select summary enable
snmp trap select status disable
snmp trap select minor disable
snmp trap select clear_minor disable

By this means, the trap traffic can be reduced.

«
...
90
91
92
93
94
...
»

Содержание MSB-2000


















































































































Отзывы:

Нет отзывов

Похожие инструкции для MSB-2000

Бренд: Yaesu Страницы: 2

Бренд: Zenith Страницы: 44

Бренд: Seiki Страницы: 75

AVerTV MCE 116 Plus

Бренд: Avermedia Страницы: 1

Бренд: Daewoo Страницы: 82

Бренд: Finlux Страницы: 120

Бренд: GE Страницы: 55

Бренд: Philips/Magnavox Страницы: 40

Бренд: Samsung Страницы: 264

Бренд: Samsung Страницы: 56

Бренд: Samsung Страницы: 99

Бренд: Samsung Страницы: 99

Бренд: Samsung Страницы: 134

Beovision MX1500

Бренд: Bang & Olufsen Страницы: 55

Бренд: RCA Victor Страницы: 32

Бренд: Sharp Страницы: 28

Бренд: Sharp Страницы: 44

Бренд: Magnum Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды