manualshive.com logo in svg

Sony MSB-2000, Руководство по эксплуатации

Поделиться
Скачать
Sony MSB-2000 Скачать руководство пользователя страница 39

39

List of Menus

(

In tx-rx mode

)

Item number

Category

Item

Arguments

Function

C013

setup (Tx)

video_rate

auto

The video ES bit rate is calculated
automatically from the TS rate and audio
settings. An 'A' appears after the numeric
value.

manual

The video ES bit rate can be specified in

4.000 to  7.500  to 50.000 units of 2 kbps. If a certain degree of error

occurs, this is controlled to be below the
setting value.
Argument unit Mbps
When video_enc mode is IMX:
30.000, 35.000, 40.000, 45.000, 50.000
Mbps
When chroma mode is 420:
4.000 to 15.000 Mbps
In other cases:
6.000 to 30.000 Mbps

Notes

• When the MSBA-20IP is installed, keep

ts_rate within 35.000 Mbps.

• If “N014:maintenance video_rate” is set to

“extended,” and video_encmode is other
than IMX, the minimum limit for
video_rate is 2 Mbps. Note, however, that
operation cannot be guaranteed at
present.

C014

setup (Tx)

scene_change

off

Disables scene change processing.

on

Enables scene change processing.

C016

setup (Tx)

pict_size

Sets the picture size when encoding is
performed.

• When video_system is 525:

720x480

Sets the picture size to 720x480.

720x512

Sets the picture size to 720x512.

• When video_system is 625:

720x576

Sets the picture size to 720x576.

720x608

Sets the picture size to 720x608.

C017

*

setup (Tx)

history_udata

off

History data for parameter referring re-
encoding is not included in the stream.

on

History data for parameter referring re-
encoding is included in the stream.

Note

• This is supported as an option.

• This item is effective only when

video_encmode is normal.

C018

setup (Tx)

seq_hdr_cycle

continuous

Puts the sequence header on every
picture.

interstitial

Puts the sequence header interstitially.

C021

setup (Tx)

audio_encmode

MPEG

Specifies the audio encoding as MPEG1
layerII.

LPCM

Specifies the audio encoding as linear
PCM (SMPTE 302M).

C022

setup (Tx)

mpeg_ch12_mode

stereo

Specifies the audio mode for channels 1
and 2 as stereo.

dual

Specifies the audio mode for channels 1
and 2 as dual.

off

Disables the audio for channels 1 and 2.

Содержание MSB-2000


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды