Sony MSB-2000 Скачать руководство пользователя

Страница: 52 / 113

List of Menus

(In sdi_to_asi mode)

C061

setup

ts_rate

auto

The TS rate is calculated automatically. An
‘A’ appears after the numeric value.

manual

The TS rate can be specified in units of

3.000 to 8.448 to 68.000

1 kbps. If a certain degree of error occurs,
this is controlled to be below the setting
value.
Argument unit: Mbps

Note

When the MSBA-20IP is installed, keep
ts_rate within 35.000 Mbps.

C062

setup

tx_program_no

00001 to 00200 to 65535 Specifies the program number declared in

PAT.

C063

setup

video_pid

0x0010 to 00ff to 1ffe

Specifies the video PID.

C064

setup

mpeg_ch12_pid

0x0010 to 0101 to 1ffe

Specifies the PID for MPEG audio
channels 1 and 2.

C065

setup

mpeg_ch34_pid

0x0010 to 0102 to 1ffe

Specifies the PID for MPEG audio
channels 3 and 4.

C066

setup

lpcm_pid

0x0010 to 0100 to 1ffe

Specifies the PID for linear PCM audio.

C067

setup

pat_version

0 to 31

Specifies the PAT version number.

C068

setup

pat_interval

1 to 33 to 100

Sets the PAT generation interval.
Unit: 1 ms

C069

setup

pmt_version

0 to 31

Specifies the PMT version number.

C070

setup

pmt_interval

1 to 33 to 100

Sets the PMT generation interval.
Unit: 1 ms

C071

setup

pcr_pid

0x0010 to 00fe to 1ffe

Specifies the PID for PCR.

C072

setup

pcr_interval

1 to 33 to 100

Sets the PCR generation interval.
Unit: ms

C073

setup

program_map_pid

0x0010 to 00c8 to 1ffe

Specifies the PID for PMT.

C074

setup

network_pid

0x0010 to 0064 to 1ffe

Specifies the PID for NIT.

C075

setup

tx_packet_size

188

Specifies the output TS packet size as 188
bytes.

204

Specifies the output TS packet size as 204
bytes.
(16 bytes of dummy data inlucluded.)

Note

When an MSBA-20IP board is installed,
the TS packet size for an MPEG stream
output through RTP is fixed at 188 bytes,
irrespective of this setting.

C076

setup

tx_asi_mode

packet

Outputs output TS in packet mode.

burst

Outputs output TS in burst mode.

C111

setup

pri_pid_base

0x0010 to 00c0 to 1ff7

Specifies the base PID for transferring
private data.

C112

setup

tx_umid

off

Disables UMID.

Enables UMID. PID is “pri_pid_base” +0

C113

setup

tx_line_data1

off

Disables uncompressed line data
processing of 1st line.

Enables uncompressed line data
processing of 1st line.
PID is “pri_pid_base” +1.

Item number

Category

Item

Arguments

Function

Содержание MSB-2000


















































































































Результаты поиска

Содержание MSB-2000

Отзывы:

Похожие инструкции для MSB-2000

Бренды по названию

Популярные бренды

Sony MSB-2000, Руководство по эксплуатации

Результаты поиска

Содержание MSB-2000

Отзывы:

Похожие инструкции для MSB-2000

Бренды по названию

Популярные бренды