manualshive.com logo in svg

Sony MSB-2000, Руководство по эксплуатации

Поделиться
Скачать
Sony MSB-2000 Скачать руководство пользователя страница 81

81

List of Menus

T043

status

link_duplex

–

In all modes, when link_status is “up” this
shows the communications mode, as
follows:
When link_status is “up” and there is a full-
duplex connection: “full-duplex”
For a half-duplex connection: “half-duplex”
If link_status is “down,” “--------” is output.
Note that when the MSBA-20IP board is
not installed, “RTP option is not mounted”
is output.

T044

status

ether_rx_packet

–

In all modes, the number of Ethernet
packets received by the MSBA-20IP in the
most recent one-second interval is shown.
The maximum output value is “65535.”
That is to say, if 65535 or more packets
are received in a second, the output is
“65535.”
Note that when the MSBA-20IP board is
not installed, “RTP option is not mounted”
is output.

T045

status

ether_rx_error

–

In all modes, out of the Ethernet packets
received by the MSBA-20IP in the most
recent one-second interval, the number of
packets in which an FEC error was
detected is shown.
The maximum output value is “255.” That
is to say, if there were 255 or more error
packets in a second, the output is “255.”
Note that when the MSBA-20IP board is
not installed, “RTP option is not mounted”
is output.

T046

status

rtp_rx_port_no

–

In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm)
mode, the port No. of the rtp packets
currently being received (udp port) is
output.
In sdi_to_asi/sdti-cp_to_asi mode, outputs
“--------” to indicate that this is invalid.
Permitted values:
50000

≤

rx_port_no

≤

65534, and

rx_port_no=0
For rx_port_no=0, to indicate that no rtp
packets are received, “--------” is output.
Note that when the MSBA-20IP board is
not installed, “RTP option is not mounted”
is output.

T047

status

rtp_rx_packet

–

In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm)
mode, outputs the number of RTP packets
received from the network in the most
recent one-second interval.
In sdi_to_asi/sdti-cp_to_asi mode, outputs
“--------” to indicate that this is invalid.
The maximum output value is “65535.”
That is to say, if 65535 or more RTP
packets are input in a second, the output is
“65535.”
Note that when the MSBA-20IP board is
not installed, “RTP option is not mounted”
is output.

Item number

Category

Item

Arguments

Function

Содержание MSB-2000


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды