Sony MSB-2000 Скачать руководство пользователя страница 53

Страница: 53 / 113

List of Menus

(In sdi_to_asi mode)

C114

setup

tx_line_data2

off

Disables uncompressed line data
processing of 2nd line.

Enables uncompressed line data
processing of 2nd line.
PID is “pri_pid_base” +1.

C115

setup

tx_line_base

12 to 21

Specifies the line number of the
uncompressed line. This line and the
following line can be transferred as
uncompressed lines.

C116

setup

tx_vanc_data

off

Disables ancillary data processing in the
vertical blanking interval.

Enables ancillary data processing in the
vertical blanking interval. PID is
“pri_pid_base” +2.

C117

setup

tx_vanc1_did

0x 00 to ff

Specifies the DID for vertical blanking
interval ancillary data.

C118

setup

tx_vanc1_sdid

0x 00 to ff

Specifies the SDID for vertical blanking
interval ancillary data.

C119

setup

tx_vanc2_did

0x 00 to ff

Specifies the DID for vertical blanking
interval ancillary data.

C120

setup

tx_vanc2_sdid

0x 00 to ff

Specifies the SDID for vertical blanking
interval ancillary data.

C121

setup

tx_vitc_data

off

Disables VITC private data transfer.

Enables VITC private data transfer.
PID is “pri_pid_base” +3.

C124

setup

tx_udata1

off

Disables getting user data1 from the UDP
port, via the MSBA-20IP.

Enables getting User data1 from the UDP
port, via the MSBA-20IP.
PID is “pri_pid_base” +6.

C125

setup

tx_udata1_port

05000 to 09000 to 65535 Sets the UDP port No. for picking up user

data1 from the MSBA-20IP.

C126

setup

tx_udata1_rate

1 to 30

Specifies rate for getting user data1 from
the MSBA-20IP.
Unit: Mbps

C127

setup

tx_udata2

off

Disables getting user data 2 from the UDP
port, via the MSBA-20IP.

Enables getting user data 2 from the UDP
port, via the MSBA-20IP.
PID is “pri_pid_base” +7.

C128

setup

tx_udata2_port

05000 to 09001 to 65535 Sets the UDP port No. for picking up user

data 2 from the MSBA-20IP.

C129

setup

tx_udata2_rate

1 to 30

Specifies rate for getting user data 2 from
the MSBA-20IP.
Unit: Mbps

Item number

Category

Item

Arguments

Function

Содержание MSB-2000


















































































































Результаты поиска

Содержание MSB-2000

Отзывы:

Бренды по названию

Популярные бренды

Sony MSB-2000, Руководство по эксплуатации

Результаты поиска

Содержание MSB-2000

Отзывы:

Бренды по названию

Популярные бренды