— 69 —
KD-34XBR2
12-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
All capacitors are in µF unless otherwise noted. pF : µµF 50WV or less are not
indicated except for electrolytics and tantalums.
All electrolytics are in 50V unless otherwise specifi ed.
All resistors are in ohms. K = 1000, M = 1000K.
Indication of resistance, which does not have one for rating electrical
power, is as follows: Pitch : 5mm
Rating electrical power :
1
/
4
W
1
/
4
W in resistance,
1
/
10
W and
1
/
8
W in chip resistance.
: nonfl ammable resistor.
: fusible resistor.
: internal component.
: panel designation and adjustment for repair.
All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
Readings are taken with a color-bar signal input.
Readings are taken with a 10M
Ω
digital multimeter.
Voltages are DC with respect to ground unless otherwise noted.
Voltage variations may be noted due to normal production tolerances.
All voltages are in V.
S : Measurement impossibillity.
: B+line.
: B-line. (Actual measured value may be different).
: signal path. (RF)
Circled numbers are waveform references.
12-1. CIRCUIT BOARDS LOCATION
RESISTOR
: RN METAL FILM
: RC SOLID
: FPRD NONFLAMMABLE CARBON
: FUSE NONFLAMMABLE FUSIBLE
: RW NONFLAMMABLE
WIREWOUND
: RS NONFLAMMABLE METAL
OXIDE
: RB NONFLAMMABLE CEMENT
:
ADJUSTMENT RESISTOR
COIL
: LF-8L MICRO INDUCTOR
The components identified by shading and
!
symbol are critical for safety.
Replace only with part number specified.
The symbol
indicates a fast operating fuse and is displayed on the
component side of the board. Replace only with fuse of the same rating as
marked.
The components identifi ed by
X
in this basic schematic diagram
have been carefully factory-selected for each set in order to
satisfy regulations regarding X-ray radiation. Should replacement
be necessary, replace only with the value originally used (Refer
to Safety Related Adjustments on page 33).
When replacing components identifi ed by
Y
, make the
necessary adjustments as indicated. If the results do not meet
the specifi ed value, change the component identifi ed by
X
and
repeat the adjustment until the specifi ed value is achieved.
When replacing the parts listed in the table below, it is important
to perform the related adjustments.
Part Replaced (
Y
)
D BOARD:
D8004, D8014, IC6503, IC8001,
IC8003, IC8004, R6590, R8016,
R8021, R8028, R8041, R8042,
R8044, R8072, R8073, R8074,
R8077, R8078, R8080, R8081,
R8082, R8091, R8095
Adjustment (
X
)
D BOARD:
RV8001, RV8002
CAPACITOR
: TATANTALUM
: PS STYROL
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED POLYESTER
: MPP METALIZED
POLYPROPYLENE
: ALB BIPOLAR
: ALT HIGH TEMPERATURE
: ALR HIGH RIPPLE
SECTION 12: DIAGRAMS
REFERENCE INFORMATION
C Board
A Board
D Board
HA Board
HB Board
W Board
S Board
U Board
(Mounted to
U Bracket)
B Board
QM Board
QI Board
(All 3 Boards
below shield)
Les composants identifies par un trame et une marque
!
sont critiques pour
la securite. Ne les remplacer que par une piece portant le numero specifie.
Le symbole
indique une fusible a action rapide. Doit etre remplace par
une fusible de meme yaleur, comme maque.
Содержание KD-34XBR2 - 34" Hdtv Fd Trinitron Wega
