SOMFY animeo Скачать руководство пользователя | Manualshive

Страница: 34 / 55

background image

animeo KNX 4 AC Motor Controller

30.01.2019

WM/DRM 220-230 V AC



2011-2019, SOMFY Activites SA



50 avenue du Nouveau Monde



74300 Cluses



France

34/55

6.6.4 Send starting value on Bus power return

Default value:



No

Selection options:



Yes



No

If this parameter is stopped, the current state of the input is transmitted with the bus voltage return. If this pa-
rameter is set to “No”, the current state of the input is not transmitted.

6.6.5 Contact A and B Cyclic sending of status

Default value:



No cyclic sending

Selection options:



No cyclic sending



On



Off



On and Off

With this parameter it is defined whether the corresponding switch value of the communication object should
be transmitted cyclically.

•

No cyclic sending

The switching value of the communication object is not transmitted cyclically.

•

On

If the object value is “1”, this is transmitted cyclically. If the object value changes by flank change at the local
input or reception of a telegram on “0”, the cyclic sending stops.

•

Off

If the object value is “0”, this is transmitted cyclically. If the object value changes by flank change at the local
input or reception of a telegram on “0”, the cyclic sending stops after “1”.

•

On and Off

If the object value is “1” or “0”, this is transmitted cyclically. If the object value changes by flank change at the
local input or with reception of a telegram, the current object value is transmitted cyclically.

6.6.6 Cyclic sending

Default value:



5 seconds

Selection options:



1

– 3600 seconds

With this parameter the time intervals are defined in which the corresponding object value should be trans-
mitted cyclically.

H

Please beware that cyclical supervision time of the receiver is approximately 4 times higher than that of

the transmitter.

«
...
32
33
34
35
36
...
»

Содержание animeo
























































Отзывы:

Нет отзывов

Похожие инструкции для animeo

Бренд: LAZER Страницы: 13

Бренд: Latento Страницы: 60

Бренд: Easy Quick Страницы: 11

Бренд: Radio Shack Страницы: 2

Бренд: Samsung Страницы: 60

Бренд: Baintech Страницы: 7

Бренд: Baicheng Innovations Страницы: 32

Бренд: Sunx Страницы: 2

Бренд: Hama Страницы: 40

Бренд: Rave Sports Страницы: 16

Бренд: Kargo Master Страницы: 5

Бренд: Omnicomm Страницы: 20

Бренд: omnicharge Страницы: 12

Бренд: Parker Страницы: 2

Бренд: Park Tool Страницы: 2

Бренд: ParaZero Страницы: 17

Бренд: Yakima Страницы: 7

Бренд: Yakima Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды