SOMFY animeo Скачать руководство пользователя | Manualshive

Страница: 8 / 55

background image

animeo KNX 4 AC Motor Controller

30.01.2019

WM/DRM 220-230 V AC



2011-2019, SOMFY Activites SA



50 avenue du Nouveau Monde



74300 Cluses



France

8/55

Connected to ...

Cabling

Twisted pair

Max. length

Motors

Min.: 4 x 0.75 mm²/18 AWG
Max.: 4 x 2.5 mm²/13 AWG

-

150 m

Push button

Min.: 3 x 0.6 mm/22 AWG
Max.: 3 x 2.5 mm²/13 AWG

Recommended

100 m

Group control

Min.: 3 x 0.6 mm/22 AWG
Max.: 3 x 1.5 mm²/15 AWG

Recommended

50 m

KNX Bus

2 x 0.8 mm/20 AWG

Required, corresponding to
KNX topology guidelines

230 V AC

Min.: 3 x 1.5 mm²/15 AWG
Max.: 2 x 2.5 mm²/13 AWG

4 Settings in the delivery state

The Motor Controller KNX can be used in the delivery state also without prior programming by the ETS soft-
ware. Practical presets are implemented in the device. These settings apply to all four motor outputs.

•

Move times UP/DOWN, CLOSED/OPEN = 5 minutes

•

Connection of local conventional push buttons is possible

The local push button inputs are assigned directly to the motor outputs: Push button input 1 controls motor
output 1 (fig. 1). The motor outputs can be controlled through bridging the wire at the push button inputs
when required (fig. 2).

4.1 Function of the Reset/Prog button

H

The basic settings in the KNX Motor Controller can be made using this push button. These basic set-

tings are possible only in the delivery state, before the device with the ETS was programmed, or after the
device was unassigned by the ETS.
The basic settings are overwritten by the settings in the ETS.

«
...
6
7
8
9
10
...
»

Содержание animeo
























































Отзывы:

Нет отзывов

Похожие инструкции для animeo

LevelMaster 7100

Бренд: ABB Страницы: 28

Ability Smart Sensor

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 20

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Parrot Страницы: 19

Бренд: Parrot Страницы: 88

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 2

Бренд: Parrot Страницы: 11

CK 3000 Evolution

Бренд: Parrot Страницы: 8

CK 3000 Evolution

Бренд: Parrot Страницы: 106

StudSensor HD25

Бренд: Zircon Страницы: 2

Бренд: Yeti Страницы: 19

Бренд: veba Страницы: 11

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Multiple G9F18 AU000

Бренд: Genesis Страницы: 3

Бренд: Viking Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды