solexx Garden Master G-512 Скачать руководство пользователя | Manualshive

Страница: 1 / 29

background image

ADAPT8, INC - MAKERS OF SOLEXX™ GREENHOUSES 1-877-476-5399

ASSEMBLY INSTRUCTIONS

12’ X 8’ X 8’9” Garden Master

G-512 (3.5mm)

This kit includes (3) double-decker benches, (2) hanging rods and (1) Louver

.

Assembly Required

-

All pipe has been precut - (No cutting is required.)

It is important to panel the greenhouse frame once it is completed and before it is rained on.

The protective coating on the fittings is to protect the fittings from rust due to moisture or

condensation. The protective coating was not designed for the volume of water produced when

the fittings are rained on for a period of time with out the paneling on the greenhouse.

TOOLS PROVIDED:

A. ¼” nut driver

TOOLS NEEDED:

A. VARIABLE SPEED DRILL
B. SCREWDRIVER
C. LONG SHARP KNIFE
D. TAPE MEASURE
E. STEP LADDER
F. PLIERS
G. 2-3 tubes “Clear” 100% silicone (We recommend IS800 Silicone Rubber Adhesive Sealant) & a

Caulking Gun

H. 8 oz. can of “Clear” PVC CEMENT (Available at a hardware store). **
I. DUCT TAPE

**Follow the instructions on the glue can. Do not apply glue if it is colder than the

instructions indicate for proper use.

u

NOTE: GLUE DRIES VERY QUICKLY! Hold pipe into fitting for 30 seconds until the glue has set.

Please read instructions carefully and refer to the diagrams.

uu

Attention:

There are two types of frame tubing in your kit. The Composite Tubing is a heavier thick-walled tubing
that has a gray fiber weave throughout (looks like a fiber texture) while the PVC tubing is a thin-walled
tubing. The super strong Composite Tubing will be used for the structural areas of the greenhouse frame.
The PVC is used in areas where the pipe needs to be flexible to bend or in non-structural areas.

Feb 20

12’ Garden Master (3.5mm) Page 1

1
2
3
...
»

Содержание Garden Master G-512






























Отзывы:

Нет отзывов

Похожие инструкции для Garden Master G-512

Бренд: Halls Greenhouses Страницы: 48

Canopia Base Kit

Бренд: Palram Страницы: 18

CANOPIA HARMONY 6x4/2x13

Бренд: Palram Страницы: 151

Бренд: GardenMeister Страницы: 50

Бренд: ClearSpan Страницы: 19

Бренд: Dancover Страницы: 16

Бренд: Dancover Страницы: 34

Бренд: Palram Страницы: 23

Бренд: Mercia Garden Products Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды