Sokkia SDL30 Скачать руководство пользователя страница 81

Страница: 81 / 87

egu

22. Regulations

For users in the US

WARNING:

Changes or modifications to this unit not

expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

NOTE:

This equipment has been tested and found to

comply with the limits for a Class A digital device pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

when the equipment is operated in a commercial

environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

For users in California

WARNING

: Handling the cord on this product or cords

associated with accessories sold with this product will

expose you to lead, a chemical known to the State of

California to cause birth defects or other reproductive harm.

Wash hands after handling

For users in Canada

This Class A digital apparatus meets all requirements of

Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Class A respecte toutes les

exi-gences du Réglement sur le matériel brouilleur du

Canada.

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 81 / 87

Результаты поиска

Содержание SDL30

Отзывы: