Sokkia SDL30 Скачать руководство пользователя страница 79

Страница: 79 / 87

ifi

tio

SDL50:

Electronic Measurement

0.8mm (0.03in.) (with BIS20/30)

1.5mm (0.06in.) (with BGS40/50/50G)

1.7mm (0.047in.) (with BAS55)

Visual Measurement

2.0mm (0.08in.) (with BGS40/50/50G)

2.5mm (0.06in.) (with BAS55)

Distance

±10mm (less than 10m measurement)

±(0.1% x D) (10 to 50m measurement)

±(0.2% x D) (more than 50m measurement)

(D: measured distance, unit: m)

Measuring modes:

Single / Repeat / Average / Tracking /

Wave-and-Read (selectable)

Measuring time:*2

Single / Repeat approx. 2.5 sec.

Average No. of measurements set

x approx. 2.5 sec.

Tracking approx. 1 sec.

Automatic

compensator: Magnetic damping and pendulum

mechanism

Compensation range:

±15

′

Wave-and-Read

Recommended brightness level for measurement

150 lx or more

Recommended speed for waving of staff

0.5Hz (3 passings of the staff through the

vertical position in 3 seconds)

Measuring range

Waving angle:5 to 10

either side of the vertical position

Height :

0.5 to 4m

Distance:

5 to 50m

Recommended staff*3: BGS series

BAS55 (up to heights of 3m)

When measuring outdoors with minimal atmospheric motion,

the staff set up in natural sunlight and luminosity at the surface

of the staff equal to 20lx.

When measuring to a staff set up outdoors in fine to cloudy

conditions.

*1, 2 These specifications may change depending on the weather

conditions and measurement conditions.

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 79 / 87

Результаты поиска

Содержание SDL30

Отзывы: