Sokkia SDL30 Скачать руководство пользователя страница 42

Страница: 42 / 87

Sur

• Point number input

Step 4:

Press

to ready the instrument for point

number input.

Step 6:

Press

twice to ready the instrument for

point number input.

(See "8.4 Flow of Recording Data".)

• Attribute setting

Step 6:

Press

to ready the instrument for attribute

setting. (See "8.4 Flow of Recording Data".)

• Go and Return setting

Step 4:

Press

to display the Go and Return Setting

Screen. (See "8.3 Double-run Measurement".)

• Storing backsight elevation

Steps 3 and 10: Even after power off, backsight elevation is

stored or turning point is stored as the next

backsight elevation. Since this value is the

same as the value in the setting out elevation

mode, the backsight elevation is stored to

whichever mode is set last. (See "11.3 Setting

Out Elevation".)

• Reviewing stored data

Steps 4 and 6: Press

to display the contents of the

selected JOB. (See "13.1 Data Check and Edit".)

• Manually inputting measurement data

Steps 4 and 6: Press

. Measurement data can now be

input manually. (See "8.4 Flow of Recording

Data".)

Notes:

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 42 / 87

Результаты поиска

Содержание SDL30

Отзывы: