Sokkia SDL30 Скачать руководство пользователя страница 72

Страница: 72 / 87

r Pr

oce

dur

•

Saving measurement values during correcting the reference

value of the sensor and power off

• Steps 9, 12 and 14:

"Data keep" screen asks whether or not you

want to save the measurement values during

setting internal constants.

Select "Yes" to save measurement values

and turn power off. When power is turned on

again and page 1 of the Config. menu is

selected, Screen Status at last power off is

displayed.

Select "No" to cancel measurement values

and turn power off.

•

Difference calculations:

• Step 15: If the tripod is turned and repeat measurements taken:

Value at position A = {[(1st reading on staff a) + (1st

reading on staff b)] + [(2nd

reading on staff a) – (2nd reading

on staff b)]} / 2

Value at position B = {[(1st reading on staff a) + (1st

reading on staff b)] + [(2nd

reading on staff a) – (2nd reading

on staff b)]} / 2

Difference = absolute value of [(value at position A) –

(value at position B)]

If the tripod is not turned and only one set of

measurements are taken:

Value at position A = [(reading on staff a) – (reading on

staff b)]

Value at position B = [(reading on staff a) – (reading on

staff b)]

Difference = absolute value of [(value at position A) –

(value at position B)]

Notes:

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 72 / 87

Результаты поиска

Содержание SDL30

Отзывы: