Sokkia SDL30 Скачать руководство пользователя страница 50

Страница: 50 / 87

agi

eco

13. Displaying Recorded Data

Data recorded in Height difference measurement mode or Elevation

measurement mode can be edited.

Use the Record Setting Mode to check data and display the number of

recorded points.

13.1 Data Check and Edit

Check the contents saved in the currently selected JOB.

Attributes can be changed.

1 In menu mode, select "REC" and

then select "Review."
The last recorded data in the

currently selected JOB is displayed.

2 Display the data that you want to

review.
Press

to display the previously

displayed data.

• Attributes can be changed in the following order only: BS

(backsight point)

FS (foresight point)

IS (intermediate sight)

FIX (fixed point)

Off

DEL (delete). (Example: Data

recorded as IS (intermediate sight) can be changed to FIX (fixed

point), Off or DEL (delete), but not to BS (backsight point) or FS

(foresight point).

• Point number and measurement results cannot be edited.

Important:

Procedure

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 50 / 87

Результаты поиска

Содержание SDL30

Отзывы: