Sokkia SDL30 Скачать руководство пользователя страница 80

Страница: 80 / 87

ifi

tio

Staff face remains sighted in the reticle throughout the entire

waving movement.

Power

Power supply:

Rechargeable Li-ion battery (BDC46B)

Battery state indicator: 4 levels

Working duration:

more than 16 hours (at 25°C)

Charging time:

about 2.5 hours*4 (using CDC68)

(BDC46B)

Nominal voltage:

7.2V

Storage temperature range:-20 to 35°C (-4 to 95°F)

(CDC68)

Input voltage:

with EDC113A/113C:110 to 240VAC

50/60Hz

with EDC113B:110 to 125VAC

50/60Hz

Charging temperature range:0 to 40°C (32 to 104°F)

Storage temperature range: -20 to 65°C (-4 to 149°F)

Charging can take longer than the times stated above when

temperatures are either especially high or low.

General

Display:

128 x 32 dot matrix LCD with illuminator

Keypad:

8 keys (7 keys on front panel;1 key on side

panel)

Auto power-off:

On (instrument powers off if not used for

30 min.) / Off (selectable)

Data output:

RS-232C compatible

Circular level sensitivity: 10

′

/2mm

Operating temperature range:-20 to 50°C (-4 to 122°F)

Storage temperature range:-40 to 70°C (-40 to 158°F)

Water resistance:

IPX4

Dimensions:

158 (W) x 257 (D) x 182 (H) mm

(6.2 (W) x 10.1 (D) x 7.2 (H) inch)

Weight (with battery):

about 2.4kg (5.3lb)

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 80 / 87

Результаты поиска

Содержание SDL30

Отзывы: