Sokkia SDL30 Скачать руководство пользователя страница 2

Страница: 2 / 87

SURVEYING INSTRUMENTS

Thank you for selecting the Digital Level SDL30/50.

•

Please read this operator's manual carefully before using this

product.

•

Verify that all equipment is included. See "20.1 Standard Equip-

ment".

•

SDL30/50 has a function to output data saved in SDL30/50 to a

connected computer. Commands operations from a computer

can also be performed. For details, refer to the “Output Formats

and Command Explanations (SDL Edition)” manual and ask your

local dealer.

•

The specifications and general appearance of the instrument are

subject to change without prior notice and without obligation by

Sokkia Topcon Co., Ltd. and may differ from those appearing in

this manual.

•

The content of this manual is subject to change without notice.

•

Some of the diagrams in this manual may be simplified for easier

understanding.

SDL30

Digital Level

SDL50

OPERATOR'S MANUAL

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 2 / 87

Результаты поиска

Содержание SDL30

Отзывы: