Sokkia SDL30 Скачать руководство пользователя страница 29

Страница: 29 / 87

Sur

5 Press

to start measurement.

A beep tone sounds and the display

blinks. Consecutive arrows are

displayed to indicate the progress of

measurement.

When measurement is completed, a

beep tone sounds twice and the staff

readings (Rh) and horizontal distance

(Hd) are displayed.

Measure

• During measurement, if direct sunlight or strong light enters the

eyepiece and measurement cannot be performed,

"Measurement error" or "Too bright" is displayed (see "17.

Warnings and Error Messages"). Shield the eyepiece from the

light source using your body or cover the eyepiece with your

hand and resume measurement. Conversely, measurement

cannot be performed when light conditions are too dark.

• Measurement cannot be performed when the staff is waved too

fast.

• Measurement cannot be performed when the staff is waved from

side to side (left to right). "Measurement error" is displayed (see

"17. Warnings and Error Messages").

Important:

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 29 / 87

Результаты поиска

Содержание SDL30

Отзывы: