Sokkia SDL30 Скачать руководство пользователя страница 6

Страница: 6 / 87

Rea

This Fir

•

Do not use under thunderous weather conditions. This unit is

conductive and if struck by lightning, death or injury could result.

•

Handle with care when using near high voltage cables or

transformers. This unit is conductive and contact could result in

electric shock.

•

When mounting the instrument to the tripod, tighten the centering

screw securely. Failure to tighten the screw properly could result in

the instrument falling off the tripod, causing injury.

•

Tighten securely the leg fixing screws of the tripod on which the

instrument is mounted. Failure to tighten the screws could result in

the tripod collapsing, causing injury.

•

Do not carry the tripod with the tripod shoes pointed at other

persons. A person could be injured if struck by the tripod shoes.

•

Keep hands and feet away from the tripod shoes when fixing the

tripod in the ground. A hand or foot stab wound could result.

•

Tighten the leg fixing screws securely before carrying the tripod.

Failure to tighten the screws could lead to the tripod legs extending,

causing injury.

•

Use only the specified battery charger to recharge batteries. Other

chargers may be of different voltage rating or polarity, causing

sparking which could lead to fire or burns.

•

Do not place articles such as clothing on the battery charger while

charging batteries. Sparks could be induced, leading to fire.

•

Do not use damaged power cords, plugs or loose outlets. Fire or

electric shock could result.

•

Do not use batteries or the battery charger if wet. Resultant

shorting could lead to fire or burns.

Staff

Warning

Tripod

Caution

Power Supply

Warning

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 6 / 87

Результаты поиска

Содержание SDL30

Отзывы: