Sokkia SDL30 Скачать руководство пользователя страница 44

Страница: 44 / 87

Sur

4 Measure the backsight.

The instrument takes the backsight

reading and displays the measure-

ment.

5 Select "Yes" to accept the value.

6 Measure the foresight.

The instrument calculates the differ-

ence between the measurement and

the input value, and displays the

result.

7 Move the staff by the amount shown

on the screen, then take another

foresight reading.
If "Fill" is displayed, move the staff

upward.

If "Cut" is displayed, move the staff

downward.

When the display shows '0', you have

found the specified ground point.

8 Press

or .

Height difference set-out is completed.

Set out the next ground point.

• When in this menu and setting-out has already been taken (for

the second or subsequent reading):
Step 4: The previous backsight measurement will be displayed

and the program skips to step 5.

• Storing setting out height difference:

Step 3: Even after power off, the height difference is stored.

Notes:

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 44 / 87

Результаты поиска

Содержание SDL30

Отзывы: