Sokkia SDL30 Скачать руководство пользователя страница 26

Страница: 26 / 87

Sur

7.2

Measuring in Status Mode

In status mode you can sight point A, take the staff reading

(Rh), and measure the horizontal distance (Hd) to the staff.

The procedure below is for taking single measurements. For

repeat measurements, see the notes.

1 Turn the power switch on.
2 Focus on the staff and press

Operation starts and the display blinks

while measurements are being taken.

When measurement is completed,

the staff readings (Rh) and horizontal

distance (Hd) are displayed.

• During measurement, if direct sunlight or strong light enters the

eyepiece and measurement cannot be performed,

"Measurement error" or "Too bright" is displayed (see "17.

Warnings and Error Messages"). Shield the eyepiece from the

light source using your body or cover the eyepiece with your

hand and resume measurement.

• If the SDL30/50 is subjected to shocks or vibration during use,

measurement may be impossible. Resume measurement during

more stable conditions.

Important:

Procedure

Measure

Содержание SDL30
























































































Результаты поиска

Содержание SDL30

Отзывы:

Sokkia SDL30, Руководство оператора, Страница: 26 / 87

Результаты поиска

Содержание SDL30

Отзывы: