SMC Networks JXCD1 Скачать руководство пользователя страница 84

Страница: 84 / 89

- 83 -

No.JXC

※

-OMT0007-D

ALM: ON

Alarm
generated

Check the type of alarm referring
to the Operation Manual for the
controller.

Take appropriate measures by
referring to the Operation Manual for
the controller.

⇒

16. Alarm for Motor Control (P.

)

Communication

fault

(JXC-W2A-C)

The USB
driver is not
installed

Check that the USB driver for the
conversion unit is installed.

Please install the USB driver of the

communication unit.

The USB driver's installation starts when the

communication unit is connected with PC.

Details of the installation procedure are

shown in "Installation procedure of the

JXC-W2 setting software".

Incorrect
COM port
setting

Please confirm if the correct
COM port is set to the ACT
Controller.

The COM port allocated to the controller is
different for different PC’s. Check and confirm

the COM port number with the controller

connected to the PC.

The COM port number can be checked using

the Device Manager of the PC. For details of

the COM port checking and setting methods

refer to the "JXC-W2 Controller Configuration

Software Installation Manual".

Connection
failure

Please confirm the connection
status.

Please confirm motor controller (JXC) =

communications cable = communication unit

= USB cable = PC is connected. For

example, communication cannot be

established if the connector has been

damaged.

Please confirm the power supply of motor

controller (JXC) has been turned ON.

Communication cannot be established if the

power supply is OFF.

If equipment other than the motor controller

(JXC) (PLC and measurement equipment) is

connected with PC, remove these before

checking. (There is a possibility that the

communication with other equipment

interferes in PC.)

Does not
operate at all.

Lock
release
error

When the unlock switch is turned
ON or OFF there is an unlocking
sound made.

If there is no sound of lock release, the
lock brake may be broken.

⇒

If the problem persists, please

contact SMC.

External
equipment
failure

Check that the PLC connected to
the controller operates correctly.
Test operation of the controller on
its own.

Refer to the controller operation manual
and take appropriate measures.

⇒

10.1 Memory allocation (P.

)

Unsuitable
spec.

Check if the controller’s
specifications are appropriate,
the power supply is suitable and
the controller is compatible with
the actuator.

Take appropriate measures according to
this manual.

⇒

3. Specifications (P.

)

Содержание JXCD1


























































































Результаты поиска

Содержание JXCD1

Отзывы:

SMC Networks JXCD1, Руководство по эксплуатации, Страница: 84 / 89

Результаты поиска

Содержание JXCD1

Отзывы: