Skyjack SJ20 Скачать руководство пользователя страница 68

Страница: 68 / 108

SJ20

238886ABA

Section 5 – Procedures

Wheel Reinstallation and Torquing Procedure

Rear Wheel Installation

Install the new wheel onto the rear axle.

Install the castle nut and flat washer. Finger
tighten the nut.

Rotate the wheel slowly while tightening the castle
nut to approximately 68 Nm (50 ft-lb). This is to
seat all the bearings in the wheel assembly.

NOTE

Do not over-torque the castle nut as the bearing
life would be reduced.

Loosen the castle nut to remove the torque. Do
not rotate the wheel.

Finger tighten the castle nut until it is snug.

NOTE

The castle nut should be free to rotate, with the
only restraint being the cotter pin.

Turn the castle nut back slightly until the next
cotter pin hole is visible on the spindle.

Install a 3/16” x 1-1/2” cotter pin. Make sure the
cotter pin is pushed in completely to allow the
dust cap to fit.

Bend the ends of the cotter pin to secure the
castle nut.

Install the dust cap over the castle nut. Be sure
not to damage the castle nut while installing the
dust cap.

Содержание SJ20













































































































Результаты поиска

Содержание SJ20

Отзывы:

Похожие инструкции для SJ20

Бренды по названию

Популярные бренды

Skyjack SJ20, Руководство по обслуживанию

Результаты поиска

Содержание SJ20

Отзывы:

Похожие инструкции для SJ20

Бренды по названию

Популярные бренды