Skyjack SJ20 Скачать руководство пользователя страница 75

Страница: 75 / 108

SJ20

238886ABA

Section 5 – Procedures

Battery Maintenance

E-0-3-2

CAN Heartbeat Lost

▪

An error was detected with the CAN heartbeat
communications with a registered node being guarded.

▪

Check the networked CANbus device(s) for correct
functioning.

▪

This alarm does not display or get logged on the
charger but does appear on the CAN bus via an
emergency message.

E-0-3-6

Battery temperature sensor is missing or
shorted

▪

Check sensor connections.

▪

The charger behavior when this fault occurs can be
configured. OEMs may contact Delta-Q Technologies for
more information.

▪

This error automatically clears once the condition has
been corrected.

E-0-3-8

Fan will not turn

(Fan-equipped models only)

▪

Check fan connections.

▪

Check to make sure the fan turns freely and is not
obstructed.

▪

This error automatically clears once the condition has
been corrected.

E-0-4-0

Fan voltage pulled low

(Fan-equipped models only)

▪

Check to make sure the fan turns freely.

E-0-4-5

Battery disconnected

▪

Battery disconnected

▪

Reconnect the battery or check the wiring

E-0-4-6

Invalid PDO Length

▪

Check to make sure all PDOs are valid length.

▪

This error automatically clears once the condition has
been corrected

E-0-4-7

Platform overvoltage alarm

▪

A battery or some other source has been connected to
the charger that exceeds the hardware’s design limits.

Содержание SJ20













































































































Результаты поиска

Содержание SJ20

Отзывы:

Похожие инструкции для SJ20

Бренды по названию

Популярные бренды

Skyjack SJ20, Руководство по обслуживанию

Результаты поиска

Содержание SJ20

Отзывы:

Похожие инструкции для SJ20

Бренды по названию

Популярные бренды