Skyjack SJ20 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 108

background image

74

SJ20

238886ABA

Section 5 – Procedures

Battery Maintenance

E-0-2-2

Low battery voltage while charging. Algorithm
dependent. Typically 0.1V/cell.

▪

Another device may be drawing current from the battery.

▪

Check the battery voltage and cable connections.

▪

Check battery size and condition. Batteries may be
overdischarged.

▪

Use another charger to bring the batteries above the
minimum voltage.

▪

This error automatically clears once the condition has
been corrected.

E-0-2-3

High AC voltage error (>270 VAC)

▪

AC voltage is too high. Connect charger to an AC
source that has a stable AC voltage between 85 and 270
VAC/45-65 Hz.

▪

In newer software versions this does not prevent
charging.

▪

This error will automatically clear once the condition has
been corrected.

E-0-2-4

Charger failed to turn on properly

▪

Disconnect AC input and battery for 30 seconds. If the
error persists, contact Delta-Q Technologies.

E-0-2-5

AC voltage has dipped below 80 VAC 3 times in
30 seconds

▪

AC source is unstable. This could be caused by an
undersized generator and/or input cables that are too
long or too small.

▪

Connect the charger to an AC source with a stable AC
voltage between 85 and 270 VAC/45-65 Hz.

▪

This error will automatically clear once the condition has
been corrected.

E-0-2-8

Attempt to select algorithm incompatible with
this software

▪

Update charger software, continue to use existing
algorithm* or select a different charging algorithm that is
compatible.

* Notes

▪

If selecting a different algorithm, the existing algorithm
will remain in the charger.

▪

If upgrading an existing algorithm, the existing algorithm
will be deleted. Contact Delta-Q Technologies for a
software upgrade to run the new algorithm.

E-0-2-9

Cannot transmit on CAN bus

▪

Check the physical CAN connector, electrical bus
conditions, and other CAN modules for correct
functioning. For example, check that termination
resistance is approximately 60 ohms.

E-0-3-0

CAN heartbeat timeout on Battery module

▪

May be caused by a missing heartbeat message. Check
the CAN bus battery module for correct function.

▪

This error automatically clears once the condition has
been corrected.

E-0-3-1

The Vref for the ADC measurements

has triggered an alarm

▪

Internal charger error. Disconnect AC and the battery for
a minimum of 30 seconds and retry.

▪

If the problem persists, contact Delta-Q Technologies.

▪

This error automatically clears once the condition has
been corrected.

«
...
72
73
74
75
76
...
»

Содержание SJ20













































































































Отзывы:

Нет отзывов

Похожие инструкции для SJ20

DBI SALA Pro Series

Бренд: 3M Страницы: 24

Бренд: ICP DAS USA Страницы: 6

Бренд: PAC Страницы: 9

Бренд: Contec Страницы: 7

Бренд: Dannmar Страницы: 85

InverArc 160 Plus

Бренд: HTP Страницы: 10

Бренд: DECA WELD Страницы: 56

Бренд: Aerotech Страницы: 48

Бренд: MSW Страницы: 7

Бренд: Linde Страницы: 2

Бренд: Vector Welding Страницы: 17

DIGI-ARC 160PFC MV

Бренд: Stealth Страницы: 24

Бренд: ICP DAS USA Страницы: 8

Бренд: B-TEC Страницы: 25

YUTAKI ATW-YMM-01

Бренд: Hitachi Страницы: 128

Relion 670 Series

Бренд: Hitachi Страницы: 192

Бренд: HERKULES Страницы: 15

Бренд: Mitsubishi Electric Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды