manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 9

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

9/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

3 

After transportation 

Check the device and the packaging and transportation material for 
damages caused by transportation! Never put a device into operation if 
there are visible or hidden transportation damages! 

Attention: 

After transportation, all electrical connections accessible by the customer 
must be checked! Vibrations during transportation may loosen the screws 
of clamps. 

Check mains wiring and output connections as well as control cables. 

Loose cable connections may cause overheating of clamps and cables 
and will lead to destruction of the installation. 

3.1 

Transportation locking devices 

Make sure no transportation locking material is left at the device before 
putting into operation. 

Remove labels and stickers that are not necessary for safe operation. 

4 

Storage 

Aluminum electrolytic capacitors are built into TechnoPlate Power Pack 
series and into their control components to ensure correct operation. 
These components are subject to natural ageing processes. 

Aluminum electrolyte capacitors containing liquid electrolyte age over 
time due to the electrolyte slowly drying out, depending on temperature. 

As a result, these devices should not be stored for longer than six 
months. If you keep replacement devices in storage, they should be 
integrated into systems after six months at the latest. If not, they should 
be connected to the power supply in non-operational mode for at least an 
hour before they are installed and also at least once a year to recondition 
the electrolyte capacitors.

 

Important 

Condensate may form on the external surfaces of devices if air humidity 
is high. 

This condensation may cause the external casing to corrode. It is 
therefore recommended to store these devices in a dry and/or air-
conditioned room with adequate ventilation to prevent such corrosion. 

Ensure that the ventilation openings are not covered when you mount the 
devices. Each device should be left to adjust to room temperature for a 
couple of hours after installation before it is put into operation. 

4.1 

Environmental conditions for storage 

Ambient temperature: 0 °C to +50 °C (for storage only) 
Air humidity:   

15 to 95 %, non-condensing 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды