manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 18

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

18/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

9 

The RS485 BUS connection 

There is a round four-pin socket located on the back plane of the device. 

 

 

This is used for remote RS485 BUS control of the device. 

Connect the RS485-BUS by the following scheme: 
 

 

OUTPUT 

INPUT 

BUS-output 

BUS-input 

(„female“ socket) 

(„male” socket) 

The INPUT socket is used to connect the incoming BUS signal coming 
from a BUS converter or a RS485 BUS interface. 

The OUTPUT socket is used to connect the BUS terminator, if no 
successive BUS device is looped into the RS485 BUS line. 

 

Round 4-pin terminal 

RS485 signal 

1 

+ VCC (only at BUS output) 

2 

BUS A 

3 

BUS B 

4 

GND (only at BUS output) 

Attention! The 5 V DC signal that is used for the BUS terminator is 
only available at the devices 15 A / 20 V and 30 A / 20 V! 

BUS input 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды