manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 57

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

57/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

20.7.1 

Configuration of the Overload detection 

If you are in the in the “Settings” menu, press the key located beside the 

Overload detection 

line. 

The display shows: 

 

 

The voltage drop threshold can be set from 1% to 99%. 

Use the keys “STORE / STEP RESET to set the value 

The recommended value is 20-40%. 

Confirm the setting with ENTER. 

Function: 

If a direct short occurs between the anode and the part: 

The display shows: 

 

 

“OVERLOAD”

 

and a short “beep” is heard. 

The DC output is shut off. 

The LED in OFF key is flashing. 

The LED in CLR key is flashing. 

Press CLR key for alarm reset. 

Press the ON key to restart the DC power supply. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды