manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 66

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

66/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

23.2 

Current calibration 

This is the measurement setup for current calibration: 

 

 

At the digital measuring instrument, select the voltage measuring range according to the 
maximum expected voltage drop at the measuring shunt (mV-range). 

Set the DC output voltage to 20 % of the nominal output voltage. 

Start the measurement series with low current: 

10 % of nominal current 

Increase in current steps of 2 A. 

Compare measured (and then calculated) values with the values shown on the display 
of the rectifier unit. 

Consider: 

The measured voltage at the measuring shunt is a reference voltage for the actual 
current! You need to calculate the real current value that is related to the measured 
voltage. 

Example: 

The measuring shunt has a nominal current capability of 60 A. The voltage drop at the 
shunt is specified with 60 mV at 60 A (shunt with 1 mOhm). 

If you measure 6.00 mV, the DC output current is 6 A 

If you measure 30.00 mV, the DC output current is 30 A. 

If you measure 60.00 mV, the DC output current is 60 A 

Please check if your measurements are within the admissible deviation range of the 
device. If the measurements are out of admissible range, please contact the 
manufacturer. 

Make sure the DC 
cables have sufficient 
cross section for the 
maximum expected 
DC current! 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды